Crystal-clear and safe water in a SaluSpa hot tub is a must and learning how to add the proper chemicals to the water will result in the best water quality. If it is your first time or looking to improve a routine, adding the chemicals properly to the hot tub will ensure an enjoyable soothing time spent in the hot tub. This guide will help teach you how to add chlorine to hot tub systems and maintain balance and order in the hot tub for better quality water.
How Do I Put Chemicals in My Hot Tub?
Adding the proper chemicals to hot tub water is an art. First, you must ensure that the water chemistry is not out of line. Obtain water chemistry test strips for the first step you must take to determine what it is that your hot tub has in the water.
This must be done to rule out that the alkalinity and ph levels of the water are not way off. When adding the chemicals, the pump system should be on so the chemicals are dispersed through the air and massage jets properly. Never add the chemicals directly to the hot tub cover or the cartridge cleaner. This will damage it.
Instructions to Follow When Adding Chemicals to a Spa:
To add chemicals to a spa, you really want to follow these steps:
- Remove the spa cover and turn the jets on
- Use test strips to test the water
- If you have any sanitizers such as granular chlorine or bromine, you want to add those in SLOWLY to the jets
- Wait 20 minutes before adding any other chemicals
- After 2 hours of the water circulating, retest the water readings again
Read More: SaluSpa Water Care: Chemicals Guide for Clean Safe Water
First Time Adding Chemicals to a New Hot Tub
You need to give the first time adding chemicals to a hot tub setup careful attention, so ensure to first give the spa a complete cleaner treatment to remove all manufacturing residues. When determining what sanitizers or balancers to add to the hot tub, be sure to take some readings in to establish what your baseline readings are before adding any hot tub chemicals.
First-Time Chemical Sequence
- Fill the spa with fresh water to the appropriate level.
- Run the spa’s pump system for 30 minutes without the addition of any chemicals.
- Test the water with strips for pH, alkalinity, and hardness.
- If needed, add a pH adjuster (If, after testing, the pH level is below 7.2, add pH increaser to the hot tub).
- After waiting 4 hours, add the primary sanitizer.
- After the water has circulated for 24hours, add a shock treatment.
Adding Shock to Hot Tub
Adding a shock treatment to the hot tub water eliminates any contaminants that may be present and helps to restore the sanitizer’s effectiveness. Spa shock should be used weekly or after heavy usage. The oxidizer helps to keep water fresh between filter cleanings by breaking down organic matter that normal sanitizers may miss.
Steps for Adding Shock:
- Test the current chlorine levels in the water before shocking the water.
- Calculate the shock’s dosage based on the volume of water in the hot tub.
- With the pump running, add the shock product.
- Keep the hot tub cover off for 20 minutes after the shock product has been added.
- Wait 8 hours before using the spa again.
How Do I Add Chlorine to My Hot Tub?
When adding chlorine to hot tub systems, be consistent. For optimal sanitization, do not let the chlorine levels drop below 3-5 ppm.
Use granular chlorine for a quick disolution right before you want to correct the water quality.
Chlorine Levels Action Required
| Chlorine Level | Water Condition | Action Required |
| Below 1 ppm | Unsafe | Add 2 tablespoons chlorine |
| 1-3 ppm | Low | Add 1 tablespoon chlorine |
| 3-5 ppm | Ideal | Maintain current routine |
| Above 5 ppm | High | Stop adding, wait 24 hours |
Daily Chlorine Maintenance Checklist
- Check test strips each morning
- Add small chlorine doses as needed
- Clean cartridge cleaner weekly
- Rinse massage jets monthly
- Replace water every 3 months
Adding Chemicals to SaluSpa Best Practices
Adding chemicals to Saluspa models requires knowing how much water your specific unit can hold since most SaluSpa hot tubs hold 177-254 gallons, affecting how much chemical you can add. Always measure accurately and never mix chemicals outside the spa.
SaluSpa Chemical Storage Tips:
- Keep chemicals in cool, dry location
- Store away from pump system and electrical components
- Separate bromine sanitizer from chlorine products
- Check expiration dates quarterly
- Use dedicated measuring cups for each chemical type
FAQs
Here are some frequently asked question given Below:
Can I Add all Chemicals to My Hot Tub at Once?
No, add chemicals separately with 20-30 minutes between each addition to prevent reactions.
How Often Should I Test my SaluSpa Water?
Test water 2-3 times weekly or before each use for accurate chemical balance.
Whats the Difference Between Shock and Regular Chlorine?
Shock is a concentrated oxidizer; regular chlorine maintains daily sanitization levels.
Should the Pump Run When Adding Chemicals?
There is equal distribution of the chemicals through the air jets when the pump runs.
How long After Adding Chemicals Can I Use My Hot Tub?
If you added regular chemicals, wait 20 minutes; if you added spa shock treatment, wait 8 hours.
Conclusion
Learning how to add chemicals to a SaluSpa hot tub is beneficial to the longevity of your equipment and achieves safe soaking. There are specific protocols and routines pertaining to maintenance of spa systems and when you add chemicals you are protecting your investment while achieving quality.
Regular testing, keeping the pump on when adding chemicals and steady sanitizer levels are keys to success. These methodical procedures will provide a much cleaner hot tub while you keep your SaluSpa in great shape.
About Author
